Aspire Cleito 0.4ohm SS316 Coils

Aspire Cleito 0.4ohm SS316 Coils

  • Earn 50 Points Every $20 Spent
    1000 points = $10.00 savings instore and online
    1000 points = $20.00 DOUBLE savings on any e juice!

Share
Login to earn Reward Points for sharing!
Aspire Cleito 120 0.16ohm Coils

Aspire Cleito 120 0.16ohm Coils

Aspire Cleito 0.4ohm Coils

Aspire Cleito 0.4ohm Coils

Aspire Cleito 0.4ohm SS316 Coils

CA$19.99 Earn 50 Reward Points
In stock
Only 4 left
SKU
Aspire Cleito 0.4ohm SS316 Coils

Aspire Cleito 0.4ohm coils deliver maximum airflow and vapour production so you will experience amazing flavour profiles. The unique coil design replaces the whole chimney greatly increasing effective cross sectional airflow providing fantastic flavor and vapor efficiency. The Cleito 0.4 SS316L coils are made with stainless steel wire allowing you can use your device in both wattage mode and temperature control mode. The Aspire Cleito 0.4ohm Coils will satisfy vapers looking for a direct to lung ("DTL") draw.  Direct to lung inhale is drawing in the vapour directly to lungs similar to smoking a shisha or hookah as opposed to a traditional cigarette. The vapour is dense, produces big clouds and is commonly referred to as “sub-ohm vaping”. Sub-ohm can be defined as a coil that is below 1.0ohm.The higher density vapour will give a more intense throat hit so it’s important to reduce the level of nicotine to 3-6mg or it may be too strong. Also it’s good to take into consideration the VG/PG (Vegetable Glycerin/Propylene Glycol) consistency of your e-liquid.  It’s best to use an e-liquid that has a lower PG ratio and a higher VG ratio.  PG provides a harsher throat hit, while VG adds to vapour density.

Please note: These coils are ONLY compatible with Aspire Cleito  & Aspire EXO tanks

 Includes:

1 x Pack of Aspire Cleito  coils 0.4ohm SS316L recommended wattage is 55-65W/ temperature control mode 450-530? (5pcs/pkg)

 

Important: Priming your coils is one of the most important steps before using a new tank/clearomizer and a new coil/atomizer. Priming your coil ensures you won't burn your coil before taking a hit. It also makes sure that the coil lasts as long as possible.

Step 1. Drop e-liquid in the center of the coil ensuring the juice is soaked up by the cotton and let it slide down so it hits the cotton and wire. Repeat this process on the wick holes on the side of the coil. The juice will soak the cotton and this will ensure that you won't experience a dry hit.

Step 2. Attach your tank and fill with e-liquid then leave it to stand for a minute or two, so that the juice in the tank gets soaked up by the coil/atomizer too.

Step 3. After you have primed the coil and let it sit for a few minutes you should fire your device below the recommended wattage and slowly increase in smaller intervals to ensure your atomizer does not burn out right away. It's recommended that you don't fire your device at maximum recommended wattage until you've puffed on it approximately 10 times.

More Information
Colour N/A
Coil OHM 0.4 OHM
Coil/Wire Type Cotton, Stainless Steel (SS316)
Brand Aspire
Compatible Tank Apire K4 Tank, Aspire Cleito/Cleito EXO Tank
Draw Type Direct Lung (DL), Sub Ohm
Watts/Temp 50w-70w
Write Your Own Review
You're reviewing:Aspire Cleito 0.4ohm SS316 Coils
Your Rating
We found other products you might like!