SMOK TFV8 Baby X4 Coils-0.15ohm

SMOK TFV8 Baby X4 Coils-0.15ohm

SMOK TFV8 baby V8-Q2 0.4OHM Coils for only CA$19.99, by Smoktech

SMOK TFV8 Baby Q2 Coils-0.4ohm

SMOK TFV8 Baby T6 Coils-0.2ohm

SMOK TFV8 Baby T6 Coils-0.2ohm

SMOK TFV8 Baby X4 Coils-0.15ohm

CA$24.99
Availability: In stock
Only 13 left
SKU
SMOK TFV8 Baby X4 Coils-0.15ohm
Reward Points You will earn 62 Points for purchasing this product.

The SMOK TFV8 Baby Turbo Engines Replacement Coils are powerful cores that are compatible with the SMOK TFV8 Baby Beast Tank & TFV8 Big Baby Beast.

The V8 BABY-X4 atomizer heads features a double barrel, quadruple coil setup and is designed to enhance flavor while still allowing higher power vaping. They have a wattage range of 30-70W with optimal performance between 45-60W for the perfect balance between flavour orientation and vapor production. The V8 BABY-X4 are also wicked with top-shelf pure organic cotton for the best vaping experience.

V8-BABY-X4 coils will satisfy vapers looking for a direct to lung ("DTL") draw.  Direct to lung inhale is drawing in the vapour directly to lungs similar to smoking a shisha or hookah as opposed to a traditional cigarette. The vapour is dense, produces big clouds and is commonly referred to as “sub-ohm vaping”. Sub-ohm can be defined as a coil that is below 1.0ohm.The higher density vapour will give a more intense throat hit so it’s important to reduce the level of nicotine to 3-6mg or it may be too strong. Also it’s good to take into consideration the VG/PG (Vegetable Glycerin/Propylene Glycol) consistency of your e-liquid.  It’s best to use an e-liquid that has a lower PG ratio and a higher VG ratio.  PG provides a harsher throat hit, while VG adds to vapour density.

Includes:
 
1 x Pack of TFV8-V8 BABY-X4 0.15ohm coil- Recommended wattage is 30-70W/ Best at 45-60W (5/pkg)

 

Specs:

-“Double Barrel” design
-0.15 ohm resistance
-Organic Cotton
-Recommended Wattage: 30-70W / Best 45-60W
 
Compatible with:
 
 

Important: Priming your coils is one of the most important steps before using a new tank/clearomizer and a new coil/atomizer. Priming your coil ensures you won't burn your coil before taking a hit. It also makes sure that the coil lasts as long as possible.

Step 1. Drop e-liquid in the centre of the coil ensuring the juice is soaked up by the cotton and let it slide down so it hits the cotton and wire. Repeat this process on the wick holes on the side of the coil. The juice will soak the cotton and this will ensure that you won't experience a dry hit.

Step 2. Attach your tank and fill with e-liquid then leave it to stand for a minute or two, so that the juice in the tank gets soaked up by the coil/atomizer too.

Step 3. After you have primed the coil and let it sit for a few minutes you should fire your device below the recommended wattage and slowly increase in smaller intervals to ensure your atomizer does not burn out right away. It's recommended that you don't fire your device at maximum recommended wattage until you've puffed on it approximately 10 times.

More Information
Coil OHM 0.15 OHM
Coil/Wire Type Cotton, Kanthal
Brand Smoktech
Compatible Tank Joyetech ProCore Aries Tank, Smok V8 Stick, SMOK TFV8 Baby Tank, SMOK TFV8 Big Baby Tank, SMOK TFV12 Baby Prince, SMOK TFV12 Big Baby Prince, Vaporesso Cascade, Vaporesso Cascade Baby SE, Vaporesso NRG Tank, Vaporesso NRG SE
Draw Type Direct Lung (DL), Sub Ohm
Watts/Temp 40w-85w