Aspire Cleito Pro Mesh Coils

Aspire Cleito Pro Mesh Coils

  • Earn 50 Points Every $20 Spent
    1000 points = $10.00 savings instore and online
    1000 points = $20.00 DOUBLE savings on any e juice!

Share
Login to earn Reward Points for sharing!
Aspire Cleito EXO 0.16ohm Coils

Aspire Cleito EXO 0.16ohm Coils

Aspire Proteus 0.25ohm Coil

Aspire Proteus 0.25ohm Coil

Aspire Cleito Pro Mesh Coils

CA$27.99 Earn 70 Reward Points
In stock
Only 1 left
SKU
Aspire Cleito Pro Mesh Coils

The SMOK TFV8 Baby Turbo Engines Replacement Coils are powerful cores that are compatible with the SMOK TFV8 Baby Beast Tank & TFV8 Big Baby Beast.

The V8 BABY-Q2 atomizer heads offer the highest resistance out of all the coils brought to you by SMOKtech. The 0.4 ohms utilizes dual vertical coils which offer amazing flavours from devices that operate at a lower wattage. They have a wattage range of 40-80W with optimal performance between 55-65W. The V8 BABY-Q2 are also wicked with top-shelf pure organic cotton for the best vaping experience.

V8 BABY-Q2 coils will satisfy vapers looking for a direct to lung ("DTL") draw.  Direct to lung inhale is drawing in the vapour directly to lungs similar to smoking a shisha or hookah as opposed to a traditional cigarette. The vapour is dense, produces big clouds and is commonly referred to as “sub-ohm vaping”. Sub-ohm can be defined as a coil that is below 1.0ohm.The higher density vapour will give a more intense throat hit so it’s important to reduce the level of nicotine to 3-6mg or it may be too strong. Also it’s good to take into consideration the VG/PG (Vegetable Glycerin/Propylene Glycol) consistency of your e-liquid.  It’s best to use an e-liquid that has a lower PG ratio and a higher VG ratio.  PG provides a harsher throat hit, while VG adds to vapour density.
 

Included:
 
1 x Pack of TFV8-V8 BABY Q2 0.4ohm coil- Recommended wattage is 55-65W/ Best at 40-80W (5/pkg)
 
Specs:
 
-Pure Taste
-Organic Cotton
-Kanthal Vertical Heating Element
-Resistance: 0.4 ohm
-Recommended Wattage: 40W - 80W / Best 55W - 65W
 

Important: Priming your coils is one of the most important steps before using a new tank/clearomizer and a new coil/atomizer. Priming your coil ensures you won't burn your coil before taking a hit. It also makes sure that the coil lasts as long as possible.

Step 1. Drop e-liquid in the center of the coil ensuring the juice is soaked up by the cotton and let it slide down so it hits the cotton and wire. Repeat this process on the wick holes on the side of the coil. The juice will soak the cotton and this will ensure that you won't experience a dry hit.

Step 2. Attach your tank and fill with e-liquid then leave it to stand for a minute or two, so that the juice in the tank gets soaked up by the coil/atomizer too.

Step 3. After you have primed the coil and let it sit for a few minutes you should fire your device below the recommended wattage and slowly increase in smaller intervals to ensure your atomizer does not burn out right away. It's recommended that you don't fire your device at maximum recommended wattage until you've puffed on it approximately 10 times.

More Information
Colour N/A
Coil OHM 0.15 OHM
Coil/Wire Type Kanthal, Clapton, Mesh
Brand Aspire
Compatible Tank Aspire Cleito/Cleito EXO Tank
Draw Type Direct Lung (DL), Sub Ohm
Watts/Temp 50w-70w
Write Your Own Review
You're reviewing:Aspire Cleito Pro Mesh Coils
Your Rating
We found other products you might like!