Uwell's Crown 3 is the new and improved sub ohm tank from Uwell. It has a 24.5mm diameter chassis with a 5.0ml juice reservoir. The Crown 3 features a top fill system to expose filling ports for easy and convenient refilling. It has three adjustable airflow slots at the bottom which allows for a smooth, effective airflow while providing ample cooiling.
The Crown 3 also has an improved chimney and structural design that reduces leakage and e-juice condensation. New to the Uwell's Crown 3 is it's innovative Plug and Pull replacement coil which has a threadless design that reinforces seals to prevent leakage. Each coil features a vertical coil arrangement that has triple vertical wicking slots for rapid wicking. The Crown 3's Pull and Plug coils provide two resistance options: 0.25ohm SS316 coil with a recommended wattage range of 80-90W and can be run in both temperature and wattage mode, 0.5ohm SS316 coil with a recommended wattage range of 70-80W and can also be run in temperature or wattage mode.
It also comes equipped with the Crown 3 Key to improve coil changing and tank cleaning. The Crown 3 has surpassed previous models with its new and improved upgrades optimized for a perfect balance of vapor and flavor production.
The Uwell Crown 3 will satisfy vapers looking for a direct to lung ("DTL") draw. Direct to lung inhale is drawing in the vapour directly to lungs similar to smoking a shisha or hookah as opposed to a traditional cigarette. The vapour is dense, produces big clouds and is commonly referred to as “sub-ohm vaping”. Sub-ohm can be defined as a coil that is below 1.0ohm.The higher density vapour will give a more intense throat hit so it’s important to reduce the level of nicotine to 3-6mg or it may be too strong. Also it’s good to take into consideration the VG/PG (Vegetable Glycerin/Propylene Glycol) consistency of your e-liquid. It’s best to use an e-liquid that has a lower PG ratio and a higher VG ratio. PG provides a harsher throat hit, while VG adds to vapour density.
1 x Crown 3 Tank
1 x 0.25ohm SUS316 Parallel Coil (Pre-installed) Recommended Wattage is 80-90W
1 x 0.5ohm SUS316 Parallel Coil Recommended Wattage is 70-80W
1 x Replacement Glass Tube
Features and Specs:
-24.5mm Tank Diamenter
-5mL Juice Capacity
-Superior Stainless Steel Construction
-Quartz Glass Reinforcement
-Crown III Parallel Coil Design
-Plug-Pull Replacement Mechanism
-0.25ohm SUS316 Parallel Coil - rated for 80-90W
-0.5ohm SUS316 Parallel Coil - rated for 70-80W
-Anti-Leak Threaded Top-Fill Method
-Precision Tri Auxiliary Adjustable Airflow
-Widebore Drip Tip (Vibrant Colorways Options Available)
-24K Gold Plated Contact
Important: Priming your coils is one of the most important steps before using a new tank/clearomizer and a new coil/atomizer. Priming your coil ensures you won't burn your coil before taking a hit. It also makes sure that the coil lasts as long as possible.
Step 1. Drop e-liquid in the center of the coil ensuring the juice is soaked up by the cotton and let it slide down so it hits the cotton and wire. Repeat this process on the wick holes on the side of the coil. The juice will soak the cotton and this will ensure that you won't experience a dry hit.
Step 2. Attach your tank and fill with e-liquid then leave it to stand for a minute or two, so that the juice in the tank gets soaked up by the coil/atomizer too.
Step 3. After you have primed the coil and let it sit for a few minutes you should fire your device below the recommended wattage and slowly increase in smaller intervals to ensure your atomizer does not burn out right away. It's recommended that you don't fire your device at maximum recommended wattage until you've puffed on it approximately 10 times.