Uwell Crown 4 UN2 0.23ohm Coils

Uwell Crown 4 UN2 0.23ohm Coils

  • Earn 50 Points Every $20 Spent
    1000 points = $10.00 savings instore and online
    1000 points = $20.00 DOUBLE savings on any e juice!

Login to earn Reward Points for sharing!
Vaporesso Skrr QF Mesh Coil 0.2ohm

Vaporesso Skrr QF Mesh Coil 0.2ohm

SMOK NORD 1.4ohm Coil

SMOK NORD 1.4ohm Coil

Uwell Crown 4 UN2 0.23ohm Coils

CA$17.99 Earn 45 Reward Points
In stock
Uwell Crown 4 UN2 0.23ohm

New to the Uwell's Crown Series is it's innovative Crown 4 Stainless Steel Plug and Pull Replacement 0.23ohm Coil ONLY compatible with the Crown 4 tank. They have a threadless design that reinforces seals to prevent leakage. Each coil features a vertical coil arrangement that has triple vertical wicking slots for rapid wicking. Coils are wicked with organic cotton and come in a packs of 4. The Crown 4 coil system has been optimized for the perfect balance of vapour and flavour production. The Plug and Pull mechanism is great for a fast and easy replacement process.

The Uwell Crown 4 UN2 0.23 ohm SS316 coils can be used in regular wattage mode at 60-70w and will satisfy vapers looking for a direct to lung ("DTL") draw.  Direct to lung inhale is drawing in the vapour directly to lungs similar to smoking a shisha or hookah as opposed to a traditional cigarette. The vapour is dense, produces big clouds and is commonly referred to as “sub-ohm vaping”. Sub-ohm can be defined as a coil that is below 1.0ohm.The higher density vapour will give a more intense throat hit so it’s important to reduce the level of nicotine to 3-6mg or it may be too strong. Also it’s good to take into consideration the VG/PG (Vegetable Glycerin/Propylene Glycol) consistency of your e-liquid.  It’s best to use an e-liquid that has a lower PG ratio and a higher VG ratio.  PG provides a harsher throat hit, while VG adds to vapour density.


4 x Uwell Crown 4 UN2 0.23 ohm FeCrAl Coils.           Recommended Wattage is 60-70W (4/pkg)


Important: Priming your coils is one of the most important steps before using a new tank/clearomizer and a new coil/atomizer. Priming your coil ensures you won't burn your coil before taking a hit. It also makes sure that the coil lasts as long as possible.

Step 1. Drop e-liquid in the center of the coil ensuring the juice is soaked up by the cotton and let it slide down so it hits the cotton and wire. Repeat this process on the wick holes on the side of the coil. The juice will soak the cotton and this will ensure that you won't experience a dry hit.

Step 2. Attach your tank and fill with e-liquid then leave it to stand for a minute or two, so that the juice in the tank gets soaked up by the coil/atomizer too.

Step 3. After you have primed the coil and let it sit for a few minutes you should fire your device below the recommended wattage and slowly increase in smaller intervals to ensure your atomizer does not burn out right away. It's recommended that you don't fire your device at maximum recommended wattage until you've puffed on it approximately 10 times.

More Information
Colour N/A
Coil OHM 0.23 OHM
Coil/Wire Type Cotton, Mesh
Brand UWell
Compatible Tank Uwell Crown 3 Tank
Draw Type Direct Lung (DL), Sub Ohm
Watts/Temp 60w-70w
Write Your Own Review
You're reviewing:Uwell Crown 4 UN2 0.23ohm Coils
Your Rating
We found other products you might like!