SMOK Baby V2 S2

SMOK Baby V2 S2

  • Earn 50 Points Every $20 Spent
    1000 points = $10.00 savings instore and online
    1000 points = $20.00 DOUBLE savings on any e juice!

Share
Login to earn Reward Points for sharing!
SMOK Baby V2 S1

SMOK Baby V2 S1

Voopoo UFORCE N1 0.13ohm Coils

Voopoo UFORCE N1 0.13ohm Coils

SMOK Baby V2 S2

CA$15.99 Earn 40 Reward Points
In stock
SKU
SMOK Baby V2 S2

The SMOK TFV8 V2 Baby Mesh S Series Replacement Coils are powerful cores that are compatible with the SMOK TFV8 V2 Baby Beast Tank.

The V2 BABY Mesh S series atomizer heads offer the best performance through a stick mod brought to you by SMOKtech. The 0.15 ohms utilizes quadruple vertical coils which offer amazing flavours from devices that operate at a lower wattage. They have a wattage range of 30-70W with optimal performance between 45-60W. The V2 BABY Mesh are also wicked with top-shelf pure organic cotton for the best vaping experience.

V2 BABY Mesh coils will satisfy vapers looking for a direct to lung ("DTL") draw.  Direct to lung inhale is drawing in the vapour directly to lungs similar to smoking a shisha or hookah as opposed to a traditional cigarette. The vapour is dense, produces big clouds and is commonly referred to as “sub-ohm vaping”. Sub-ohm can be defined as a coil that is below 1.0ohm.The higher density vapour will give a more intense throat hit so it’s important to reduce the level of nicotine to 3-6mg or it may be too strong. Also it’s good to take into consideration the VG/PG (Vegetable Glycerin/Propylene Glycol) consistency of your e-liquid.  It’s best to use an e-liquid that has a lower PG ratio and a higher VG ratio.  PG provides a harsher throat hit, while VG adds to vapour density.
 

Included:
 
1 x Pack of TFV8 BABY V2 S2 Mesh 0.15Ω coil- Recommended wattage is 30-70W/ Best at 45-60W (3/pkg)
 
Specs:
 
-Pure Taste
-Organic Cotton
-Kanthal Vertical Heating Element
-Resistance: 0.15 ohm
-Recommended Wattage: 40-80W/ Best 60-70W
 

Important: Priming your coils is one of the most important steps before using a new tank/clearomizer and a new coil/atomizer. Priming your coil ensures you won't burn your coil before taking a hit. It also makes sure that the coil lasts as long as possible.

Step 1. Drop e-liquid in the center of the coil ensuring the juice is soaked up by the cotton and let it slide down so it hits the cotton and wire. Repeat this process on the wick holes on the side of the coil. The juice will soak the cotton and this will ensure that you won't experience a dry hit.

Step 2. Attach your tank and fill with e-liquid then leave it to stand for a minute or two, so that the juice in the tank gets soaked up by the coil/atomizer too.

Step 3. After you have primed the coil and let it sit for a few minutes you should fire your device below the recommended wattage and slowly increase in smaller intervals to ensure your atomizer does not burn out right away. It's recommended that you don't fire your device at maximum recommended wattage until you've puffed on it approximately 10 times.

More Information
Colour N/A
Coil OHM 0.15 OHM
Coil/Wire Type Cotton, Mesh
Brand Smoktech
Compatible Tank SMOK Baby V2
Draw Type Direct Lung (DL), Sub Ohm
Watts/Temp 40w-80w
Write Your Own Review
You're reviewing:SMOK Baby V2 S2
Your Rating
We found other products you might like!